Knowledgebase : Network Time Servers (NTS) > NTS-6001
This update is available for the following units: NTS-6002 Firmware: http://box.galsys.co.uk/firmware/nts-6002-firmware.zip [http://firmware.galsys.co.uk/nts-6002-firmware-12-1.gfw]Click here [https://support.galsys.co.uk/index.php?/Knowledgebase/Artic...
This is the Hardware Manual for the NTS-6001. It will provide information regarding the installation and setup of the hardware. It also covers debugging and troubleshooting the unit.
This is the Web Configuration Manual for the NTS-6001 - FOR VERSION 10 AND BELOW ONLY. It will provide information regarding the setup and configuration of the unit. If you require VERSION 11 manuals, please click here [http://support.galsys.co.uk/ind...
This is the Web Configuration Manual for the NTS-6001 - FOR VERSION 11 ONLY. It will provide information regarding the setup and configuration of the unit. If you require VERSION 10 AND BELOW manuals, please click here [http://support.galsys.co.uk/ind...
This article provides useful information for our customers who wish to setup their devices in redundancy mode. Please note that the information in this article applies to the NTS-6001 and 6002 units only, running Firmware 11 or higher. If your time serve...
If you have GPS: 1. Navigate to the Web Interface and login with your credentials. 2. From the navigation menu, select LOGS and click GPS ANTENNA DEBUG. 3. Select ENABLE DEBUG. Allow the debugger to run for atleast 1 minute. 4. Select DOWNLOAD LOG ...
PLEASE NOTE: These debugging instructions are for VERSION 10 AND BELOW. For debugging instructions for VERSION 11 AND ABOVE, please click here [http://support.galsys.co.uk/index.php?/Knowledgebase/Article/View/73/1/debugging-nts-6001-gps-and-radio-v11]. ...
PLEASE NOTE: These debugging instructions are for VERSION 10 AND BELOW. If you require Version 11 and above instructions, please click here [http://support.galsys.co.uk/index.php?/Knowledgebase/Article/View/73/1/debugging-nts-6001-gps-and-radio-v11]. Fo...
This article contains Firmware 12 upgrade instructions for the NTS-6001 only. PLEASE NOTE: It is NOT possible to upgrade from Version 8 or below to Version 12. If you are ABLE to access the web interface, you can follow Section (A). If you are UNABLE to...
If you are required to set the IP Address of the NTS-6001 manually, then first you must plug a standard USB keyboard into the unit before turning on the NTS-6001 unit. Once the unit is on please use the following steps to set the IP Address manually. ...
This article will show you how to set up NTP Authentication on your NTS-6002 or 6001. Note: This article is aimed at NTS-6002/6001 running Firmware 11 or higher. If your unit is running an older firmware, we recommend upgrading the firmware on your unit:...
Firmware 11#10 RELEASE DATE: 14/12/2016  * Fixed a potential issue when calculating delay with radio clocks (MSF, DCF, WWVB) * Updated the leap-seconds.list to account for the upcoming leap second * Updated Nginx to 1.10.2 * Updated PHP to 7.0....
Resetting the NTS-6001 BIOS Boot the unit with a monitor and keyboard attached and hit the num pad delete key repeatedly to get to the bios. In the bios go to the [EXIT] tab and then to "Load failsafe defaults" and hit [OK] in the confirm dialogu...
First, you need to connect up a monitor and keyboard to the unit. With these connected you should see the same display on the monitor as on the LCD display. Next press "Alt + F2" The Default username is "root" and the Default passowrd is "galleon" Pres...
Version 11 of the NTS-6001 firmware introduced big changes into how the unit works and how it is secured. To update your firmware, download the new firmware from the This Page [http://support.galsys.co.uk/index.php?/Knowledgebase/Article/View/3/1/nts-60...